Product Center
Home » gas cutting nozzle material chart
  • GAS CUTTING & WELDING - Nahpets

    AFN CUTTING NOZZLE Size Code Cutting Thickness (mm) Oxygen Pressure (Bar) Acetylene Pressure (Bar) Length (mm) AFN-1 10-100370 1-3 1.0 0.5 51 AFN-2 10-100371 3-8 1.5 0.5 51 AFN-3 10-100372 8-20 2.0 0.5 51 • Use with Afrox type portapak cutting attachment • Use with oxygen & acetylene gases SWAGED WELDING NOZZLE Size Code Material Thickness ...

  • Operating Data (Cut) Charts - Plasma Automation

    Operating Data (Cut) Charts The Cut Charts on the following pages are optimized to provide the best cut angle, least dross and best cut surface finish. Keep in mind that these charts provide a good starting point and that optimum cutting must be tuned to the application and materials on site. Increasing cut speed, lowering the torch standoff ...

  • Laser cutting. LASERLINE Technical. - BOConline

    the material to be cut (Fig. 1, also see the Laser Basics brochure). The intense light beam quickly heats up the workpiece and melts the material. The assist gas (also called: cutting gas) is applied to protect and cool the focusing lens and to remove the molten metal from the cut kerf at the same time. There are two cutting processes, depending on

  • View Cutting Condition Table - AMADA

    Shows the nozzle gap. Nozzle Gap is the distance between the tip of the nozzle and the material surface. Generally, the nozzle gap should be about 1.5 mm. However, when performing high-pressure assist gas (stainless or aluminum) cutting, a much smaller nozzle gap (0.3 to 0.5 mm) is recommended.

  • Oxy-Fuel Torch Tip/Nozzle Design and Selection

    Part 1 of a 2 part series. When designing or selecting an oxy-fuel machine torch cutting nozzle/tip one must consider several factors. The following are several, but not all, items to be considered 1) thickness of the steel to be cut, 2) type cutting bore (cylindrical bore or high speed/divergent bore), 3) preheat gas to be used, 4) type cutting to be conducted (shape cutting, bevel cutting ...

  • How big is a heating gas cutting nozzle?

    CUTTING NOZZLES ANM SHORT PATTERN 6 heating holes, 76 mm long. USE: Acetylene fuel gas. Art. Nr. Range Size Quantity 0768554 (10132)3 - 6 mm size 1/32” 1 0768555 (10364)5 - 12 mm size 3/64” 1 0768556 (10116)10 - 75 mm size 1/16” 1 0768557 (10564)70 - 100 mm size 5/64” 1

  • Cutting Nozzles, Arcnm Rivet Cutting Nozzle, Agnm Gouging ...

    Home. » Cutting Nozzles for gas cutting torch are available for FUEL viz. Acetylene (DA) and LPG. » Cutting nozzles for Acetylene are known as ANM nozzles while cutting nozzles for LPG are known as PNM nozzles. » Different sizes of cutting nozzles are used for cutting metal of different thickness. ANME LONG PATTERN.

  • Oxy-fuel welding and cutting - Wikipedia

    MAPP gas can be used at much higher pressures than acetylene, sometimes up to 40 or 50 psi in high-volume oxy-fuel cutting torches which can cut up to 12-inch-thick (300 mm) steel. Other welding gases that develop comparable temperatures need special procedures for safe shipping and handling.

  • How big of a nozzle do I need for a welding nozzle?

    Nozzle type PNM / PNME using 6.3mm x 10m fitted hose with resettable flashback arrestors in new condition. Pressure & consumption rates are based using the nozzle size listed next to it cutting the thickest material in the metal thickness column. PNM-E Cutting Nozzles Ordering Information

  • OXY/ACETYLENE WELDING AND CUTTNG - Weldability | Sif

    hold the blowpipe with the nozzle at right angles to the plate and apply the heating flame to the edge of the material furthest from the operator. A spade or nozzle attached to the nozzle is of assistance in holding the blowpipe steady. When the edge of the metal attains a bright red heat, operate the cutting oxygen lever and draw the blowpipe

  • Gas gives the big assist in laser cutting

    Jul 13, 2015 · To cut 0.25-in. material in CO 2 may call for a 2.5-mm-diameter nozzle; but because in a fiber laser cutting situation the kerf is usually narrower, the application may require a 3-mm-diameter nozzle. A 2.5-mm nozzle may require 2,000 cubic feet per hour (CFH), and the 3-mm nozzle may have a gas flow rate of 3,500 CFH.

  • Welding & Cutting Guide - Flexihire

    • Cutting nozzles – sizes: C-P, 8,12,15,20,24,32. • Tips and mixer – W for brazing. • Heating mixer – HT or HTP. • Heating tips – sizes: HT-PI,HT-P2,HTP-P3,HTP-P4. It is recommended LP-Gas compatible hose be used – colour coded orange. WARNING: LP-Gas regulator,mixer,tips and nozzles must not be used with acetylene. BOC pr ...

  • Gas Cutting Nozzle - Manufacturers & Suppliers in India

    We are an acclaimed name engaged in offering our precious clients a superior quality range of LPG Cutting Nozzle that is used for cutting purpose. The offered nozzle is manufactured using premium quality raw material and modern technology in line with industry standards.

  • CUTTING NOZZLES ANM TYPE - Weldability | Sif

    CCANM02W 3/64 ANM CUTTING NOZZLE CCANM03W 1/16 ANM CUTTING NOZZLE CCANM04W 5/64 ANM CUTTING NOZZLE CCANM05W 3/32 ANM CUTTING NOZZLE CCANM06W 1/8 ANM CUTTING NOZZLE For further information, contact Weldability | Sif technical support on 0870 330 7757 or email [email protected] y-sif.com Material Thickness Operating pressure Gas consumption ...

  • Gas-Cutting: Process, Techniques and Advantages | Welding

    1. Gas Cutting Torch: A specially designed gas cutting torch is shown in Fig. 7.43. The tip of the cutting torch has a larger centre opening from which a jet of oxygen comes to cut the metal. This central opening surrounded by a set of orifices (generally four) which supply the oxygen-acetylene mixture for pre-heating.

  • Portables & Gas Apparatus Equipment - Gas Cutting Nozzle ...

    Wholesale Distributor of Portables & Gas Apparatus Equipment - Gas Cutting Nozzle, Super Sentinel Direct Coupling & Flashback Arrestor, Epoch Torch Propane Heavy Duty Cutting Solution and Oxy-Fuel Cutting Tip offered by TOSS WELDTRONICS, Pune, Maharashtra.

  • What kind of nozzle for gas cutting torch?

    » Cutting Nozzles for gas cutting torch are available for FUEL viz. Acetylene (DA) and LPG » Cutting nozzles for Acetylene are known as ANM nozzles while cutting nozzles for LPG are known as PNM nozzles. » Different sizes of cutting nozzles are used for cutting metal of different thickness

  • Cut charts - Plasma Automation

    4-12 HPR260 Auto Gas Instruction Manual 5 Cut charts The following Cut charts show the consumable parts, cutting speeds and the gas and torch settings required for each process. The numbers shown in the Cut charts are recommended to provide high-quality cuts with minimal dross. Because of

  • Oxyfuel Cutting - Process and Fuel Gases - TWI

    The oxyfuel process is the most widely applied industrial thermal cutting process because it can cut thicknesses from 0.5mm to 250mm, the equipment is low cost and can be used manually or mechanised. There are several fuel gas and nozzle design options that can significantly enhance performance in terms of cut quality and cutting speed.

  • What kind of nozzle is used to cut steel?

    Echoing this, it is the device at the piping tip of commonly used oxy-acetylene flame used for cutting steel. The small metallic part that dispenses the flame. There is a variety of gas cutting nozzle types in the market. Each is chosen depending on the size, torch type, material, bore diameter, thickness to be cut, and the pressure of oxygen.

  • How to Use a Cutting Torch Tip Chart | The Harris Products Group

    The Harris Cutting Tip Chart contains information on tip style/size selection, oxygen gas pressure settings (pre-heat flame and cutting stream), cutting oxygen gas orifice (center hole) sizing, fuel gas pressure settings, hose size recommendation, travel speed (machine cutting) and cut quality illustrations.

  • CNC Plasma & Gas: Oxy-Fuel Cutting Nozzle

    Oxy-fuel Cutting Torch can be used for Acetylene and Propane cutting but with different cutting nozzle, for Propane cutting is used G03 nozzle and for Acetylene is used G02 nozzle. Oxygen pressure refers to cutting pressure before arriving at the cutting torch. Carbon rate of steel material ≤0.45%. Oxygen pressure refers to cutting pressure ...

  • PRESSURES TIMES FUEL GAS (Propane or Dec. Frac. IPM in in PSI ...

    1 - These cutcharts are a starting point. Adjustments might be necessary due to installation and material variations. 101084 (V0001314) 250-300 101080 (V0001306) 2 - Start by using these parameters and change as necessary. Save cut charts modifications to controller and paper for future use. HEATING NOZZLE 100797 (V0001305) 100797 (V0001305 ...

  • Guidelines for Gas Welding and Cutting - BOC

    18.2 Straight Line and Bevel Cutting 53 18.3 Piercing and Cutting Holes 53 19.0 Nozzle Data Section 54 19.1 BOC Welding Tips 54 19.2 BOC 2 Seat Oxy-Acetylene Cutting Nozzles 54 19.3 BOC 2 Seat Oxy-LPG Cutting Nozzles 54 19.4 BOC 3 Seat Oxy-Acetylene Cutting Nozzles 55 19.5 BOC 3 Seat Oxy-LPG Cutting Nozzles 55 20.1 Equipment Care 56

  • Cutting Torch Tips Sizes Charts | Garage Sanctum

    Cutting Torch Tips Sizes Charts. Cutting torch tips sizes chart for 3-hose machines. In a case, 2-hose machine is used, preheat pressure must be set by decreasing or eliminating oxygen flow. Each tip size is suitable for metal thickness as specified in the chart.

  • ACETYLENE - Keen Gas

    * Applicable for 3-hose machine cutting torches only. With a 2-hose cutting torch, preheat pressure is set by the cutting oxygen. ** For best results use appropriate capacity torches and 3/8" hose when using tip size 6 or larger. Torches with flashback arrestors require up to 25% more pressure as tip size increases (15 PSI maximum acetylene ...

  • Selecting plasma cutting consumables - The Fabricator

    May 22, 2019 · Cut height is the ideal height that your CNC machine and height control should maintain once the machine starts cutting and moving forward. If the torch gets more than about 0.005 in. higher than the suggested setting, expect angularity, a wider kerf, dross, and possible warpage on thin materials.

  • Buy Gas Cutting Nozzle India | Gas Cutting Nozzle Types

    Types of gas cutting nozzles. Gas cutting nozzles are supplied in various types. There are three main globally recognized and frequently used nozzles. They are supplied in different sizes, material, bore diameters, and pressure tolerance ability. This attracts a different gas cutting nozzle price on each piece.

  • The Ultimate Guide to Fiber Laser Cutting | MachineMfg

    When cutting flammable materials such as cotton, paper, the inert gas is been used. The auxiliary gas entering the nozzle can also cool the focus lens, prevent the dust from entering the lens seat to contaminate the lens and cause the lens to overheat. Most organic and inorganic materials can be cut by laser.

  • Oxy-Fuel Gas Cutting

    to attempting to cut, the material should be cleaned with a stiff wire brush to remove dirt and scale. With correct gas pressures, nozzle size, cutting torch angle and speed, the quality of freehand cutting depends upon the steadiness of the operator. IP 21874 FDAUS 0106 10K

  • Cutting Processes - Application of Oxyfuel Cutting - TWI

    a jet of oxygen to react with the material to be cut and at a flow rate sufficient to blow away the slag; Each torch should be fitted with the appropriate nozzle for the type of fuel gas. Nozzles can be of a one- or two-piece design. The nozzle type will depend on: fuel gas; manual or machine operation; manufacturer's preference